FM-1 Remote
A remote for the M-VAVE FM-1 running Baud Girl's FM-1+VA firmware, over the USB cable from Chrome or Edge. Every control sends one of the CCs in the firmware's manual: the sound of the preset that is playing, the Virtual Analog engine, the six effects, the synth's own knobs and buttons, the presets. The Sound row speaks the same numbers as SUBCH-60, so with it open in another tab one slider moves both.
- FM-1
- not connected
- Heard
- –
- SUBCH-60
- not open
Sound the preset that is playing · MIDI ch · also SUBCH-60
One slider, both engines: on an FM preset CC 74 is Brightness and 71 Feedback, on a Virtual Analog preset Cutoff and Resonance, on SUBCH-60 the VCF Freq and Res. Any of the four envelope CCs switches the preset's Envelope on, as holding ENV does. Changes mark the preset as edited; SAVE on the synth keeps them.
Virtual Analog VA presets only
FM FM presets only
Keys MIDI ch
Effects FX ch · the numbers follow the effect wherever it sits in the chain
Panel the synth's own controls
Buttons press on the way down and let go on the way up, so holding one here is holding it on the synth: SEL is shift, a long ENV switches the envelope, a long HOME switches Bluetooth. There is no SAVE: the firmware leaves CC 109 empty so a stray knob can never write the memory over and over.
Presets
Program Change on the send channel. 113-128 are the Virtual Analog pack when it is installed; without it they are M-VAVE's FM presets. SUBCH-60 takes Program Change 0-55 for its memories 1-1 to 7-8.
Keys lit by the FM-1's keybed · play them to the targets C3
Monitor what went out and what came in
Setup once, with the synth on the cable
The firmware
This page needs FM-1+VA FM-1_086 or later (the controller CCs arrived in 086). Install it from baudgirl.com/work/FM-1+VA/install in Chrome or Edge: the synth must be on M-VAVE's V15 first, the install keeps your presets and patterns, and takes about a minute. Then Save a backup on the Presets page before installing the Virtual Analog pack. The page cannot ask the synth which version it runs: the version shows under the logo at power-on and under About at the end of the GLOBE screen.
The channels
On the synth: GLO, then MIDI. Leave MIDI Channel on All (or match Send ch here) and FX Channel on 2 (or match FX ch). Keep them different: on the FX Channel every CC is an effect control, so the same channel turns the mod wheel into Filter Type and CC 7 into Reverb Mix.
With SUBCH-60
Open SUBCH-60 in another tab and switch it on, then light SUBCH-60 in the strip above. The Sound row, the keys, the mod wheel, the sustain pedal and All notes off go to both; the pages talk over a BroadcastChannel inside the browser, so there is no loopback MIDI driver to install. SUBCH-60 also hears the FM-1 directly: its keybed, arpeggiator and 64-step Sequencer all play the Juno, so the FM-1 can sequence both at once. Turn the FM-1's MASTER down to hear only the Juno.
When nothing happens
On Windows a MIDI port belongs to one program at a time: close Ableton, M-VAVE's updater, anything else holding the FM-1 (tabs in the same browser share it fine). A cable that only charges shows the screen and no port. If the synth moves but not the setting you meant, check the channels above and the Monitor: it names every CC it sends.
Source: music/hub/public/fm1/, with every CC in cc.js as the contract and the shared numbers in ../subch60/midicc.js. The CC map is Baud Girl's; this page only sends it. M-VAVE and FM-1 are M-VAVE's names; FM-1+VA is Baud Girl's firmware.